SAE J2388 Secondary Control Modifications

作者:标准资料网 时间:2024-05-15 09:04:15   浏览:8135   来源:标准资料网
下载地址: 点击此处下载
Product Code:SAE J2388
Title:Secondary Control Modifications
Issuing Committee:Adaptive Devices Standards Committee
Scope:This SAE Recommended Practice establishes a uniform procedure for assuring the manufactured quality, installed utility and performance of automotive products to the relocation, alteration, replacement and/or extension of secondary controls and systems other than those provided by the vehicle manufacturer (OEM). These products are intended to provide driving capability to persons with physical disabilities. These products function as adaptive modifications to compensate for lost or reduced function in the extremities of the driver. These include, but are not limited to the following:Cruise Control; Door Locks; Gear Selector; Hazard Flasher; Headlight Beam Selector; Heater/Vent/Air Conditioner (HVAC); Horn; Ignition/Starter; Light controls; Mirrors; Parking Brake; Power Seats; Turn Signals; Power Window Controls; and Windshield Wiper/Washer and defogger; Rear Accessories (Defogger, Wiper/Washer).The purpose of any secondary control adaptation is to provide the effective use of the motor vehicle operating systems to a driver with a disability, so that he or she may drive and operate that motor vehicle with the same degree of safety as a non-disabled driver. Thus, the adaptive equipment must be (1) accessible to the driver with a disability for whom it is designed, (2) not susceptible to inadvertent operation which may be inconvenient or dangerous for the driver and other users of the roadway, and (3) suitable by non-disabled drivers who may have a need to operate the motor vehicle whenever possible.For purpose of this document, the secondary controls listed previously have been classified according to the following protocols. The categorization of these controls, while different from other SAE publications, is reflective of the manner in which driver rehabilitation specialists determine appropriate vehicle modifications. These categories are arranged to assign priorities that allow the user to operate a vehicle in the most efficient manner possible.Mode A - These controls shall be operable by the driver while the vehicle is in operating mode. They must be accessible to the driver for which they were intended while being able to maintain control of the vehicle steering, brake and accelerator functions. Included in this group are: Cruise control 鈥淪et;鈥?Headlight Beam Selector; Horn; Turn Signals; and, Windshield Washer/Momentary Wipe.Mode B - These controls shall be operable by the driver while maintaining control of the vehicle brake function with the vehicle not in motion, as in the case of vehicle start-up or re-start necessitated by engine stall. Included in this group are: Gear Selector and Ignition/Starter.Mode C - These controls shall be at least operable by the driver when the vehicle is stationary, either temporarily or parked. Included in this group are: Cruise control 鈥淥n鈥?and 鈥淥ff;鈥?Door Locks; Hazard Flashers; Heater/Vent/Air Conditioner (HVAC); Light Controls; Mirrors; Parking Brake; Power Seats; Windshield Wiper; and Power Window Controls; Rear Accessories (Defogger, Wiper/Washer).
下载地址: 点击此处下载
Product Code:SAE AMS4347
Title:Aluminum Alloy Sheet, 1.0Mg - 0.8Si - 0.8Cu - 0.5Mn (6013-T4), Solution Heat Treated and Naturally Aged
Issuing Committee:Ams D Nonferrous Alloys Committee
Scope:This specification covers an aluminum alloy in the form of sheet.【英文标准名称】:QualificationandCertificationofResourceRecoveryFacilityOperators
【原文标准名称】:资源回收设施操作人员的资格和认证
【标准号】:ANSI/ASMEQRO-1-1994
【标准状态】:作废
【国别】:美国
【发布日期】:1994
【实施或试行日期】:
【发布单位】:美国国家标准学会(ANSI)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:认证;废物处理
【英文主题词】:wastetreatment;certification
【摘要】:
【中国标准分类号】:Z02
【国际标准分类号】:03_120_20;13_030_50
【页数】:
【正文语种】:英语